Инструкция для Shindaiwa C230

Оглавление инструкции

• Страница 1 из 25
  

  ENGLISH SHINDAIWA OWNER’S/OPERATOR’S MANUAL T230 GRASS TRIMMER T230X GRASS TRIMMER C230 BRUSHCUTTER T230 T230X C230 WARNING! Minimize the risk of injury to yourself and others! Read this manual and familiarize yourself with the contents. Always wear eye and hearing protection when operating this

• Страница 2 из 25
  

  Introduction Attention Statements General Safety Instructions Shindaiwa 230-series hand held power equipment has been designed and built to deliver superior performance and reliability without compromise to quality, comfort, safety or durability. Throughout this manual are special “Attention

• Страница 3 из 25
  

  General Safety Instructions The Properly Equipped Operator Stay Alert You must be physically and mentally fit to operate this unit safely. WARNING! Never operate power equipment of any kind if you are tired or if you are under the influence of alcohol, drugs, medication or any other substance that

• Страница 4 из 25
  

  Safety Labels IMPORTANT! Safety and Operation Information Labels: Make sure all information labels are undamaged and readable. Immediately replace damaged or missing information labels. New labels are available from your local authorized Shindaiwa dealer. READ THE OPERATOR’S MANUAL WEAR HEARING AND

• Страница 5 из 25
  

  Unit Description Using the accompanying illustrations as a guide, familiarize yourself with this unit and its various components. Understanding the product helps ensure top performance, long service life, and safer operation. See Figure 4. Ignition Switch Fuel Tank Outer Tube Throttle Trigger

• Страница 6 из 25
  

  Assembly Driveshaft/Powerhead All Models Connect the Outer Tube to the Powerhead. 1. Place the powerhead on a clean, flat surface, spark plug facing up. See Figure 6. 2. Use the 4 mm hex wrench to loosen the tube clamp screw. Tube Clamp Decal Hex Wrench Clamp Figure 6A Ignition Switch 3. Add some

• Страница 7 из 25
  

  Assembly Handlebar C230 Handle Positioning Label Ignition Switch Assemble the Handlebar. 1. Position the handle over the outer tube. See Figure 9. Make sure the throttle lever is on the right-hand side of the outer tube. Shoulder Strap 2. Attach the handle mounting bracket using the two socket-head

• Страница 8 из 25
  

  Assembly Throttle Linkage and Ignition Leads All Models Assemble and Adjust the Throttle Cable. 1. Insert the throttle-cable housing into the notch on the fan cover, and clamp the ground wire terminal between the fan cover and the outer cable adjuster nut. See Figure 13. Red Wire Black Ignition

• Страница 9 из 25
  

  Assembly Cutting Attachment Shield All Models Socket-Head Cap Screw T230 Outer Tube Upper Clamp Cutting Attachment Shield Bracket Shim Shim Nuts Clamp Screw Line Cutter Shim Shim Retaining Nut T230X/C230 Bolt Cutting Attachment Shield Mounting Plate Figure 14 Install the Cutting Attachment Shield

• Страница 10 из 25
  

  Assembly Trimmer Head C230/T230/T230X Model Holder Remove the T230 retaining plug Output Shaft Shaft Bolt Bolt Guard Model C230/T230X Output Shaft Holder B 5. Using hand pressure only, tighten the trimmer head firmly on the gearshaft. Holder A 6. Remove the hex wrench. 7. Adjust the trimmer line

• Страница 11 из 25
  

  Assembly Blade C230/T230X (continued) 5. Install blade holder “B” on the output shaft. See Figure 21. The recess in the holder must completely cover the safety clip, and must fit tightly against the blade. Blade Output Shaft Bolt Guard Blade Holder B 6. Install the bolt guard and then the blade

• Страница 12 из 25
  

  Starting the Engine IMPORTANT! Engine ignition is controlled by a two position switch mounted on the throttle housing labeled, “I” for ON or START and “O” for OFF or STOP. Make sure the cutting attachment is clear of obstructions! IMPORTANT! If the engine fails to start after several at­ tempts

• Страница 13 из 25
  

  Adjusting Engine Idle Idle Adjusting Screw The engine must return to idle speed whenever the throttle lever is released. Idle speed is adjustable, and must be set low enough to permit the engine clutch to disengage the cutting attachment. Idle Speed Adjustment WARNING! Figure 28 The cutting

• Страница 14 из 25
  

  Using a Grass Trimmer T230 Your Shindaiwa T230 Grass Trimmer may be equipped with one of several Shindaiwa trimmer head models, each with features for specific applications and/or operational requirements. NOTE: A grass trimmer head can also be fitted to the Shindaiwa C230 Brushcutter. For proper

• Страница 15 из 25
  

  Using A Brushcutter Blade C230/T230X Blade Thrust WARNING!  Before working with a bladeequipped unit, always inspect and clean the area of objects that could interfere with or damage the blade.  Never use a blade near sidewalks, fence posts, buildings or other objects that could cause injury or

• Страница 16 из 25
  

  General Maintenance IMPORTANT! MAINTENANCE, REPLACEMENT OR REPAIR OF EMISSION CONTROL DEVICES AND SYSTEMS MAY BE PERFORMED BY ANY REPAIR ESTABLISHMENT OR INDIVIDUAL; HOWEVER, WARRANTY REPAIRS MUST BE PERFORMED BY A DEALER OR SERVICE CENTER AUTHORIZED BY SHINDAIWA CORPORATION THE USE OF PARTS THAT

• Страница 17 из 25
  

  10/15-Hour Maintenance Ever y 10 to 15 hours of operation: Remove and clean the spark plug. Clean the spark plug and check the gap at the electrode.  Adjust the spark plug electrode gap to 0.024-inch (0.6 mm). If the plug must be replaced, use only a Champion CJ8 or equivalent spark plug of the

• Страница 18 из 25
  

  135-Hour Maintenance After ever y 135 hours of operation or if engine becomes hard to start and has low power. The spark arrester screen should be inspected and cleaned. Engine Cover Engine Cover Knob WARNING! Never operate the unit with a damaged or missing muffler or spark arrester! Operating

• Страница 19 из 25
  

  Long Term Storage Whenever the unit will not be used for 30 days or longer, use the following procedures to prepare it for storage:  Clean external parts thoroughly.  Drain all the fuel from the carburetor and the fuel tank. IMPORTANT! All stored fuels should be stabilized with a fuel stabilizer

• Страница 20 из 25
  

  Troubleshooting Guide ENGINE DOES NOT START What To Check Does the engine crank? Possible Cause NO Good compression? Faulty recoil starter. Fluid in the crankcase. YES Remedy Consult with an authorized servicing dealer. Internal damage. NO Loose spark plug. Tighten and re-test. Excess wear on

• Страница 21 из 25
  

  Troubleshooting Guide (continued) ADDITIONAL PROBLEMS Symptom Poor acceleration. Engine stops abruptly. Engine difficult to shut off. Cutting attachment rotates at engine idle. Excessive vibration. Cutting attachment will not rotate. Possible Cause Remedy Clogged air filter. Clean or replace the

• Страница 22 из 25
  

  The following statement only applies to United States and its territories Shindaiwa Corporation Federal Emission Design And Defect Limited Warranty Utility And Lawn And Garden Engines Shindaiwa Corporation warrants to the initial purchaser and each subsequent owner, that this utility equipment

• Страница 23 из 25
  

  NOTES 23

• Страница 24 из 25
  

  ® Shindaiwa Inc. 11975 S.W. Herman Rd. Tualatin, Oregon 97062 USA Telephone: 503 692-3070 Fax: 503 692-6696 www.shindaiwa.com Shindaiwa Corporation Head Office: 6-2-11, Ozuka-Nishi Asaminami-Ku, Hiroshima 731-3167, Japan Telephone: 81-82-849-2220 Fax: 81-82-849-2481 ©2006 Shindaiwa, Inc. Part

• Страница 25 из 25