H-SA605 5 CHANNEL CAR AMPLIFIER 5- Instruction manual HYUNDAI H-SA605
YOUR NEW HIGH FIDELITY 5 CHANNEL AMPLIFIER IS DESIGNED TO DELIVER MAXIMUM ENJOYMENT AND ONE YEAR OF TROUBLE FREE SERVICE. Features · · · · · · · · · Four Class ''AB'' High-Current Dual Discrete Drive Stages. Class ''AB'' and Technology MOSFET PWM Power Supply. Bridgeable & TRI-Mode Operation.
· · · · · · · · · · All cables should be run beneath carpets and inside trim pieces. To help minimize interference, it is best to run the power cables along the opposite side of the audio(RCA) cables. Whenever wires pass through metal, rubber or plastic grommets must be used to prevent the metal
1. After reading precaution, decide where you are going to install the unit. Also, see Fig.1. 2. Once the location has been determined, place the amplifier into position. Using a felt tip pen or pencil mark the four holes to be drilled for mounting. NEVER use the amplifier as a template for
CONNECTIONS INPUT CONNECTIONS · This amplifier will accept low level inputs. Low level is the same as line level. The low level signal is carried through RCA cables. It is preferred to use low level inputs to the amplifier if the head unit is equipped with the low level outputs. If not, you can use
POWER CONNECTIONS It is important to have good quality power and ground connections. Remember, to complete an electrical circuit, the ground connection is just as important as the positive power connection. Before any power connections are made, disconnect the ground cable at the battery. When the
SPEAKER CONNECTIONS This amplifier can operate in one, two or three channel mode. The minimum impedance for single channel (bridged/mono) operation is 2 or 8 ohms. Tri channel power is referred to stereo and mono at the same time. Minimum impedance remains the same for three channel (front /
ADJUSTMENTS 1.Set to the "H.P.F" position when the amplifier is used to drive a tweeter/midrange system. The frequencies below the crossover point will be attenuated at 12dB/octave. Permits adjustment of the crossover frequency, by rotating the knob to select any frequency between 80Hz to 1.2kHz as
Trouble Shooting Guide · Before you consult this listing, make sure the vehicle s electrical system is working properly by verifying that other electrical items (e. g. headlights, Windows, etc.) still function correctly. SYMPTOM No audio PROBABLE CAUSE Low or N.C. remote turn-on connections Blown
Specification MODEL AVERAGE OUTPUT POWER H-SA605 4 Ohms, 0.08% THD. 60 W 4 + 250 W x 1 LOW PASS FILTER 50 Hz 250 Hz HIGH PASS FILTER 80 Hz 1.2 kHz MAXIMUM OUTPUT POWER 500W + 350W FREQUENCY RESPONSE (-1dB) 10Hz 40 kHz SIGNAL TO NOISE RATIO (`A' WTD) >100dB INPUT SENSITIVITY 200mV - 6V INPUT
5- ! . · · · · · · · · · « » MOSFET PWM. TRI-mode , . «D» . 12 (Bass Boost) 0-12 RCA, . , . . 50 . . . · , - · · , ! , , . , . , . 5 . · · , . , . · · · . , , , . · · ( ) , 5,27 2 , , . . 0,5 . ; , . , , , . · , , ; HYUNDAI . , . 10 H-SA605
· · ( , ). , , . · ( , .), , . · · , , , . , . , · , . « 12 ». , , · 2 . . 0,832 . · ( , ), , +12 . , · , . ( 100 ) . 130 HYUNDAI 11 . ! H-SA605
· · , . . , · · · 4 . 3,5 3,0 . . ( .1). .1 HYUNDAI 12 H-SA605
· . RCA , . . · ( , ) RCA ( .2). . 2. HYUNDAI 13 H-SA605
· · · 2 5 «GND» . , . . . · · · · · · : , . ( . . ) , , . , . . «REMOTE» , « +» 0,5 «remote amplifier» . . , , . . . HYUNDAI 14 H-SA605
· . 4-8 , · · . . , ( .3). .3. HYUNDAI 15 H-SA605 )( .
· « .F», - . · 1,2 12 , . «L. .F», 12 . . 250 50 , . · · , . CD ( « , ¾ . «FLAT». , 200 6 . ¾ » (200 ). - . , «MIN» (6 ). , . , · 80 . , «BASS» +12 . 50 ( «L.P.F» «FLAT»). .4. HYUNDAI 16 H-SA605
· . . , , , , ( , ). . , RCA . RCA ; ; , HYUNDAI 17 H-SA605
H-SA605 4 0,08% (-1 ( . ) WTD) 60 4 + 250 50 250 80 1,2 500 + 350 10 40 x1 >100 200 6 22 ( ) =12 4 , ( 25 A x 3 ), 260 52 420 . HYUNDAI 18 H-SA605