Инструкция для Timberk THU UL 04

O

 Important!

1. To prevent an electric shock, prior to dismantling the device 
(removing the tank), unplug the device from electric mains! 2. Do 
not fill the tank with liquids other than tap water.

Other composition of liquids has an adverse effect on internal 
parts and results in a failure.
3.  Do not fill the device or the water tank with such additives as 
essential oil, flavoring substance, detergent, chemical medical 
products, warm water (over 40°), etc.
Otherwise the water tank and internal parts of the unit will be 
damaged and be broken.
4.  Do not fill water directly into the internal part of the unit or the 
atomizer.
Water inside the unit may result in failure of the device.
5.  Do not hit and do not throw the water tank. It can be damaged 
which will result In water leakage. Do not use the unit in case the 
tank is heavily hit.
Contact a maintenance service or maintenance and repair station 
immediately.
6.  Every day fill the tank with pure water and keep the unit clean.

6.  Operation of the unit

6.1  Switching on the unit

Connect the unit to electric mains. Fill the tankwith water in advance.
A musical signal will be given when the unit is connected to a power supply 
source.
Press  "On/Off"  button  (Power,  On/Off),  a  musical  signal  will  be  given  and 
the unitwill automatically start operating.
"AUTO"  mode  will  be  shown  on  the  display  screen  and  steam  will  start 
coming out of the atomizer.

The  display  screen  will  show  current  air  humidity  and  the  warm  atomizing 

mode will be switched on automatically.

Ten  seconds  after  pressing  the  power  button  a  light  atomizing  Indicator 

(preparation for operation) will be Illuminated and then will goout.

At  the  very  beginning  of  this  operation  the  atomizing  level  could  seem 

unstable  which  is  caused  bythetemperaturedifferenceand  waterquallty. 
It  will  take  some  time  for  water  to  transform  into  steam  inside  the 
atomizer's  nozzle  and  this  process  to  be  stabilized.  In  10-25  minutes  of 
operation the atomizing level will be gradually stabilized.
Heat! ng of steam wi 11 ta ke about 10-20 m I ñutes.

important!

At  first  or  repeated  use  of  the  unit  even  with  full  tank  the  water  level 
indicator,  showing  there  is  no  water,  will  be  Illuminated  on  the  display 
screen. It happens due to the fact that it takes some time for water to flow 
from the tankto a water groove.
The unitwill automatically startoperating In 2-5 minutes.
In case If all water In the tank is used, the unitwill be switched off and a 
sound  signal  will  be  given  prior  to  It  and  the"waterleverindicator  will  be 
Illuminated. In five seconds the light indicator will go out and a red light 
will be illuminated.
Add water In accordance with the manual forfurther use of the unit.

6.2  Automatic operation mode

A  temperature  and  humidity  sensor  Is  installed  Inside  the  humidifier,  when 
the  unit  Is  switched  on  or  the  automatic  operation  mode  is  selected  It 
allows 

the 

unit 

to 

Independently 

achieve 

the 

most 

favorable 

humidification level depending on room airtemperatureand humidity.

Table 2.

Room air temperature

Setting of the automatic operation mode 

(level of favorable humidity)

<19“C

65%

20-2VC

60%

22-24X

55%

>25X.

50%

In  the  automatic  mode  the  atomizing  level  Is  set  in  accordance  with  the 

difference  between  levels  of  measured  and  nominal  humidity.  The 
atomizing level in automatic mode:

Table 3.

Difference between levels of

Atomizing frequency

favorable and current humidity

(intensity indicator)

>16

Intensive mode (maximum power)

15^

Moderate mode (normal power)

<3

Light mode (low power)

Current humidity level 

exceeds the favorable one

automatic switching off

www.timberk.nj • ultrasonic humidifier