Random orbital sander ENG
but use a coarser grit size.
7. SELECTING THE RIGHT GRADE OF
SANDPAPER
Different grades of sanding paper can be
purchased from good DIY shops. Available
grades are Coarse, Medium and Fine.
Use coarse grits to sand down rough finishes,
medium grit to smooth the work and fine grit
to finish off.
The higher the grade number, the finer the grit.
For rough work start with a low grade of grit.
(e.g. 60 grit) and change to a higher, finer grade
(e.g. 100 or 120 grit) for finishing. If you use a
fine grade for rough surfaces it will soon clog
and need changing.
It is best to make a trial run on a scrap piece of
material to determine the optimum grades of
sandpaper for a particular job.
8. PAD BRAKE
Your sander is equipped with a pad brake that
prevents over-speeding of the pad. If the tool
is lifted off the work surface while the motor
is running, the brake will limit pad rotation to
avoid unwanted sanding marks and gouges.
WORKING HINTS FOR
YOUR ORBITAL SANDER
If your power tool becomes too hot, especially
when used at low speed, set the speed to
maximum and run it with no load for 2-3
minutes to cool the motor. Avoid prolonged
usage at very low speeds. Always use sand
paper that is suitable for the material you want
to sand.
Always ensure the work-piece is firmly held or
clamped to prevent movement.
Any movement of the material may affect the
quality of the sanding finish.
Start your sander before sanding and turn it off
only after you stop sanding. For the best results,
sand wood in the direction of the grain.
Do not start sanding without having the
sandpaper fitted.
Do not allow the sandpaper to wear away it will
damage the base-plate. The guarantee does not
cover base-plate wear and tear.
Use coarse grit paper to sand rough surfaces,
medium grit for smooth surfaces and
fine grit for the final surfaces. If necessary, first
make a test run on scrap material.
Use only good quality sandpaper.
The sandpaper controls the sanding efficiency,
not the amount of force you apply to
the tool. Excessive force will reduce the sanding
efficiency and cause motor overload. Replacing
the sandpaper regularly will maintain optimum
sanding efficiency.
MAINTENANCE
Your power tool requires no additional
lubrication or maintenance. There are no user
serviceable parts in your power tool. Never use
water or chemical cleaners to clean your power
tool. Wipe clean with a dry cloth. Always store
your power tool in a dry place. Keep the motor
ventilation slots clean. Keep all working controls
free of dust. If you see some sparks flashing in
the ventilation slots, this is normal and will not
damage your power tool.
ENVIRONMENTAL
PROTECTION
Waste electrical products should not
be disposed of with household waste.
Please recycle where facilities exist.
Check with your local authorities or retailer for
recycling advice.
11
10
RU-WU650-M-060726.indd 10
2006-7-26 14:10:53
Random Orbit Sander ENG Pag 06 Машина шлифовальная эксцентриковая RUS Pag 12 WU650 RU-WU650-M-060726.indd 1 2006-7-26 14:10:48
RU-WU650-M-060726.indd 2 2006-7-26 14:10:48
RU-WU650-M-060726.indd 3 2006-7-26 14:10:48
� � � � � � � � � RU-WU650-M-060726.indd 4 2006-7-26 14:10:48
A B C D E F G RU-WU650-M-060726.indd 5 2006-7-26 14:10:50
1. ON-OFF SWITCH 2. VARIABLE SPEED CONTROL 3. HAND GRIP AREA 4. HOOK AND LOOP SYSTEM 5. SANDING DISC PAD 6. DUST BAG TECHNICAL DATA Rated voltage Rated power Rated no-load speed 220V-240V~50Hz/60Hz 300W 5,000-12,000min-1 Base plate size ø125mm Sanding paper size ø125mm Orbital diameter 2.5mm Double
SAFETY INSTRUCTIONS WARNING! Read all instructions. Failure to follow all instructions listed below may result in electric shock, fire and/or serious injury. The term “power tool” in all of the warnings listed below refers to your mains-operated (corded) power tool or batteryoperated (cordless)
untrained users. e) Maintain power tools. Check for misalignment or binding of moving parts, breakage of parts and any other condition that may affect the power tools operation. If damaged, have the power tool repaired before use. Many accidents are caused by poorly maintained power tools. f) Keep
20. Do not sand magnesium material due to the risk of fire. 21. Wear eye protection when operating this tool. SYMBOLS Read the manual Warning Wear eye protection Double insulation Wear hearing protection Wear dust mask OPERATING INSTRUCTIONS 1. ON/OFF SWITCH To start your sander, depress the
but use a coarser grit size. 7. SELECTING THE RIGHT GRADE OF SANDPAPER Different grades of sanding paper can be purchased from good DIY shops. Available grades are Coarse, Medium and Fine. Use coarse grits to sand down rough finishes, medium grit to smooth the work and fine grit to finish off. The
WARRANTY STATEMENT If your WORX product becomes defective due to faulty materials or workmanship within the specified warranty period of: • 12 months from the date of purchase. We guarantee to repair or replace all defective parts free of charge, repair products subject to fair wear and tear, free
1. ВЫКЛЮЧАТЕЛЬ ПИТАНИЯ 2. РЕГУЛЯТОР СКОРОСТИ 3. ОБЛАСТЬ ЗАХВАТА РУКОЙ 4. КРЕПЛЕНИЕ БУМАГИ «НА ЛИПУЧКЕ» 5. ШЛИФОВАЛЬНАЯ ПЛАТФОРМА 6. МЕШОК ДЛЯ СБОРА ПЫЛИ ТЕХНИЧЕСКИЕ ХАРАКТЕРИСТИКИ Номинальное напряжение 220V-240V~50Hz/60Hz Потребляемая мощность Скорость на холостом ходу 300W 5,000-12,000min-1
ИНСТРУКЦИИ ПО ТЕХНИКЕ БЕЗОПАСНОСТИ ВНИМАНИЕ! Прочтите все инструкции. Невыполнение всех нижеприведенных инструкций может привести к поражению электрическим током, пожару и/или серьезным травмам. Термин “электроинструмент” во всех дальнейших предупреждениях относится к вашему электроинструменту,
ситуациях. е) Одевайтесь надлежащим образом. Не надевайте свободную одежду или украшения. Держите волосы, одежду и перчатки на удалении от движущихся частей. Свободную одежду, украшения или длинные волосы может затянуть в движущиеся части. ж) Используйте предусмотренные средства и устройства для
• • работы. Вы можете уменьшить воздействие этих химических веществ: Работайте в хорошо проветриваемом помещении Работайте со специальными средствами защиты, такими как респиратор, предназначенный для фильтрации микроскопических частиц. ДОПОЛНИТЕЛЬНЫЕ ПРАВИЛА ТЕХНИКИ БЕЗОПАСНОСТИ ПРИ РАБОТЕ С
УСЛОВНЫЕ ОБОЗНАЧЕНИЯ См. Руководство Предупреждение Наденьте защитные очки Двойная изоляция Наденьте защитные наушники Наденьте респиратор 16 ЭКСПЛУАТАЦИЯ 1. ВЫКЛЮЧАТЕЛЬ ПИТАНИЯ Для включения нажмите на нижнюю часть защищенного выключателя (позиция «I»). Для выключения нажмите на верхнюю часть
материала зависит от скорости вращения диска и типа шлифовальной бумаги. Скорость вращения диска уменьшается при сильном давлении на инструмент. Для более быстрой обработки материала не увеличивайте давление на инструмент, а используйте более грубую шлифовальную бумагу. 7. ВЫБОР ТИПА ШЛИФОВАЛЬНОЙ
ЗАЩИТА ОКРУЖАЮЩЕЙ ДЕКЛАРАЦИЯ СРЕДЫ СООТВЕТСТВИЯ Отходы электрической продукции не следует утилизировать с бытовыми отходами. Этот инструмент необходимо доставить на местный центр утилизации для надлежащей обработки. ГАРАНТИЯ Завод-изготовитель устанавливает электроинструмент срок гарантии
19 RU-WU650-M-060726.indd 19 2006-7-26 14:10:58
RU-WU650-M-060726.indd 20 2006-7-26 14:10:58