Router ENG
router.
• Insert the guide rods (C) into router base. For
maximum stability, make sure each rod goes
through both holes and protrudes out the other
side of the router base (At a maximum, the rods
must be inserted far enough into the router
base that they are supported from below base.
• Securely fasten the router to the rods by
tightening the locking screws (12). The largest
circles and arcs can be made when the guide
rods enter the side of the router where the
locking screws (12) are located.
• Mark the workpiece at the center of the desired
circle.
• Using the centering slots on the edge of the
pivot plate (22), center the pivot plate on the
center mark and attach to the workpiece with
several strips of strong tape placed over the
pivot plate in a crisscross pattern.
• Place fine adjustment guide (F) on pivot plate
(22) so the hole in fine adjustment guide (F) fits
over the steel pin.
• Adjust the position of the rods and router as
necessary to achieve the desired radius of the
circle or arc, then securely tighten wing knobs.
13. CARBON BRUSH REPLACEMENT
Always be sure that the tool is switched off
and unplugged before attempting to perform
inspection or maintenance.
There are 2 motor brushes which can be easily
accessed on either the front or back of the
motor housing.
ATTENTION:
When servicing a tool, ALWAYS use only
identical replacement parts.
STEP 1: Locate the plastic motor brush caps on
both the front and back of the motor housing.
STEP 2: Remove the threaded access cap on
accessible carbon brushes (30) with a flathead
screwdriver and turn the screw in a counter-
clockwise rotation to loosen.
STEP 3: Gently remove the old motor brush.
STEP 4: Carefully insert the replacement brush.
Ensure the brush is completely inserted into
the holder and is seated properly and is free to
move inside its holder.
STEP 5: Replace the access cap with the flat-
head screwdriver, turning clockwise to tighten.
Do not apply excessive force as this may
damage the access plug.
Note:
Always change both sets of brushes at
the same time.
MAINTENANCE
Your power tool requires no additional
lubrication or maintenance. There are no user
serviceable parts in your power tool. Never
use water or chemical cleaners to clean your
power tool. Wipe clean with a dry cloth. Always
store your power tool in a dry place. Keep the
motor ventilation slots clean. Keep all working
controls free of dust. If you see some sparks
flashing in the ventilation slots, this is normal
and will not damage your power tool.
ENVIRONMENTAL
PROTECTION
Waste electrical products should not
be disposed of with household waste.
Please recycle where facilities exist.
Check with your local authorities or retailer for
recycling advice.
WARRANTY STATEMENT
If your WORX product becomes defective due
to faulty materials or workmanship within the
specified warranty period of:
• 12 months from the date of purchase.
We guarantee to repair or replace all defective
parts free of charge, repair products subject
to fair wear and tear, free of charge, or at
our discretion,replace the unit free of charge
to ensure minimum inconvenience to the
customer. Your warranty is subject to the
following conditions:
• Proof of purchase date and a valid receipt is
produced.
• The product has not been misused.
• Unauthorized persons have not attempted
repairs.
• The product has not been used for hire
purposes.
• The product has not sustained damage
through foreign objects, substances or
accidents.
• Damage is not a result of fitting non-approved
UKR-WU600 WU600.1 WU601 WU601.1-M-060726.indd 13
2006-7-26 14:08:54
Router ENG Pag 06 Фрезерная машина RUS Pag 16 WU600/WU600.1/WU601/WU601.1 UKR-WU600 WU600.1 WU601 WU601.1-M-060726.indd 1 2006-7-26 14:08:37
UKR-WU600 WU600.1 WU601 WU601.1-M-060726.indd 2 2006-7-26 14:08:37
UKR-WU600 WU600.1 WU601 WU601.1-M-060726.indd 3 2006-7-26 14:08:37
1 16 2 3 15 6 4 5 7 26 14 9 12 10 8 11 19 20 17 30 18 13 29 UKR-WU600 WU600.1 WU601 WU601.1-M-060726.indd 4 2006-7-26 14:08:39
23 1 20 14 2 13 19 A 10 3 25 B C 11 Fig b Fig a 24 D 21 10 F E � 12 G �� �� � � � 24 � � �� H I UKR-WU600 WU600.1 WU601 WU601.1-M-060726.indd 5 2006-7-26 14:08:47
1. FINE-ADJUSTMENT KNOB FOR DEPTH-OF-CUT 2. SCALE FOR FINE ADJUSTMENT OF DEPTH-OF-CUT 3. CLAMPING LEVER 4. LEFT HANDLE 5. SCALE FOR COARSE ADJUSTMENT OF DEPTH-OF-CUT 6. DEPTH STOP 7. WING SCREW FOR DEPTH STOP 8. DUST BOOTS 9. STEP BUFFER 10. BASE PLATE 11. GUIDE PLATE 12. LOCKING SCREW FOR GUIDE
TECHNICAL DATA WU600 WU600.1 Rated voltage Rated power 1500W WU601.1 1800W 11500~28000min-1 Rated no-load speed Collet size WU601 220V-240V~50Hz/60Hz Ø6.35mm & 12.7mm Ø6.35mm & 12.7mm Ø8 &12mm Ø8 &12mm Double insulation Machine weight 4.3Kg NOISE AND VIBRATION DATA A weighted sound pressure A
SAFETY INSTRUCTIONS WARNING! Read all instructions. Failure to follow all instructions listed below may result in electric shock, fire and/or serious injury. The term “power tool” in all of the warnings listed below refers to your mains-operated (corded) power tool or batteryoperated (cordless)
untrained users. e) Maintain power tools. Check for misalignment or binding of moving parts, breakage of parts and any other condition that may affect the power tools operation. If damaged, have the power tool repaired before use. Many accidents are caused by poorly maintained power tools. f) Keep
SYMBOLS Read the manual Warning Wear eye protection Double insulation Wear ear protection Wear dust mask 10 OPERATING INSTRUCTIONS 1. INSERT THE ROUTER BIT Router Bit Selection Depending on processing and application, router bits are available in many different designs and qualities: Router bits
• When vacuuming dry dust that is especially detrimental to health or carcinogenic, use a special vacuum cleaner. motor speed to reduce the motor “kick” or torque effect to improve operator comfort and safety. 3. ON AND OFF SWITCH For starting the machine, actuate the lock-off button (16) first, and
value and actual value). Retighten wing screw again. Slide router upward again and check depth-ofcut by carrying out another trial cut. After setting the depth-of-cut, the position of the index mark (26), on the depth stop should not be changed anymore so that the currently adjusted setting can
router. • Insert the guide rods (C) into router base. For maximum stability, make sure each rod goes through both holes and protrudes out the other side of the router base (At a maximum, the rods must be inserted far enough into the router base that they are supported from below base. • Securely
accessories. To claim the guarantee, you will need to submit proof of purchase to the seller or an authorized repair agent. This warranty does not apply to accessories. This warranty applies only to the original purchaser and may not be transferred. All repairs and replacement tools will be covered
UKR-WU600 WU600.1 WU601 WU601.1-M-060726.indd 15 2006-7-26 14:08:55
1. РЕГУЛЯТОР ТОЧНОЙ НАСТРОЙКИ ГЛУБИНЫ ФРЕЗЕРОВАНИЯ 2. ШКАЛА ТОЧНОЙ НАСТРОЙКИ ГЛУБИНЫ ФРЕЗЕРОВАНИЯ 3. ФИКСИРУЮЩИЙ РЫЧАГ 4. ЛЕВАЯ РУКОЯТКА 5. ШКАЛА ДЛЯ ГРУБОЙ НАСТРОЙКИ ГЛУБИНЫ ФРЕЗЕРОВАНИЯ 6. ОГРАНИЧИТЕЛЬ ГЛУБИНЫ ФРЕЗЕРОВАНИЯ 7. ВИНТ ФИКСАЦИИ ОГРАНИЧИТЕЛЯ ГЛУБИНЫ ФРЕЗЕРОВАНИЯ 8. ЗАЩИТНАЯ МАНЖЕТА 9.
ТЕХНИЧЕСКИЕ ХАРАКТЕРИСТИКИ WU600 WU600.1 Номинальное напряжение Потребляемая мощность 1500W Скорость без нагрузки Зажим инструмента WU601 WU601.1 220V-240V~50Hz/60Hz 1800W 11500~28000min-1 Ø6.35mm & 12.7mm Ø6.35mm & 12.7mm Ø8 &12mm Ø8 &12mm Двойная изоляция Вес 4.3Kg ХАРАКТЕРИСТИКИ ШУМА И ВИБРАЦИИ
ИНСТРУКЦИИ ПО ТЕХНИКЕ БЕЗОПАСНОСТИ ВНИМАНИЕ! Прочтите все инструкции. Невыполнение всех нижеприведенных инструкций может привести к поражению электрическим током, пожару и/или серьезным травмам. Термин “электроинструмент” во всех дальнейших предупреждениях относится к вашему электроинструменту,
надевайте свободную одежду или украшения. Держите волосы, одежду и перчатки на удалении от движущихся частей. Свободную одежду, украшения или длинные волосы может затянуть в движущиеся части. ж) Если предусмотрено подсоединение устройств для удаления и сбора пыли, убедитесь, что они правильно
ДОПОЛНИТЕЛЬНЫЕ МЕРЫ БЕЗОПАСНОСТИ ПРИ РАБОТЕ С ФРЕЗЕРОМ 20 УСЛОВНЫЕ ОБОЗНАЧЕНИЯ 1. Всегда надевайте респиратор. 2. Надевайте защитные очки и защитные наушники.. 3. Для длинных волос используйте средства защиты. Не работайте в свободной одежде. 4. Если кабель питания поврежден или перерезан во время
ЭКСПЛУАТАЦИЯ 1. УСТАНОВКА ФРЕЗ Выбор фрез В зависимости от вида работы и обрабатываемого материала, фрезы различаются по форме и материалу, из которого они сделаны: Фрезы, сделанные из быстрорежущей стали (HSS), предназначены для обработки мягких материалов, таких как мягкая древесина и пластмасса.
постоянной частоты вращения под нагрузкой и ограничения пускового тока (только для WU601&WU601.1) Электронная система поддерживает частоту вращения постоянной без нагрузки и при большинстве рабочих условий. Ограничение пускового тока задерживает увеличение моторной скорости, чтобы уменьшить рывок
7. ПРОЦЕСС ФРЕЗЕРОВАНИЯ. Отрегулируйте глубину фрезерования как описано выше. Поставьте фрезер на заготовку. Включите фрезер. Ослабьте рычаг зажима, вращая его по часовой стрелке, и медленно опустите фрезер до касания ограничителя глубины фрезерования ступенчатого упора. Зафиксируйте фрезер в этом
24 13. ЗАМЕНА ЩЕТОК Внимание: Перед обслуживанием электроинструмента обязательно убедитесь, что выключатель питания выключен, а штепсель вынут из розетки. В инструменте предусмотрен облегченный доступ к щеткам с передней и задней сторон корпуса инструмента. Внимание: При обслуживании инструмента,
ДЕКЛАРАЦИЯ СООТВЕТСТВИЯ Мы, POSITEC Power Tools (Suzhou) Co., Ltd. No. 11 Yangqing Road, Loufeng Area, Suzhou Industrial Park, Jiangsu 215021, P. R. China Заявляем, что продукция, Марки WORX Фрезерная машина Моделей WU600/WU600.1/WU601/WU601.1 Соответствует положениям Директив, EC директива для
UKR-WU600 WU600.1 WU601 WU601.1-M-060726.indd 26 2006-7-26 14:09:01